Rapid Tac products were created to make removing and installing vinyl graphics faster, easier and more economical for graphics installers of all skill levels. We manufacture Vinyl Application Fluid, Adhesive Remover, Wax and Silicone Remover. When removing adhesive, removing wax and silicone residues, or performing a wet application, we have the solutions for you of the past.
Rapid Tac Application Fluid shocked installers by allowing them more control over their applications than ever before. Now what took hours could be accomplished in minutes. Using Rapid Tac Application fluid can often allow a large graphic to be installed with one person where two people were required to perform the same installation dry. Rapid Tac Application Fluid also cleans the substrate without leaving residues ensuring a contaminant free installation. It then helps to “float” the vinyl film until it is properly positioned. Rapid Tac Application Fluid’s best feature is that it effectively breaks the surface tension of the adhesive on the film allowing it to flow and bond to the substrate more effectively than even a dry application. It is now possible to achieve a full bond in as little as ninety seconds. Your customers and your reputation will benefit from higher-quality applications. Your bottom line will benefit from faster applications and less failures as well.
Keeping it simple. When your faced with removing adhesive we have your solution. Rapid Remover is a non-toxic, water-soluble adhesive remover that breaks down and removes adhesives in as little as sixty seconds! Spray it on, wait a few minutes and easily wipe away residue adhesive with a plastic squeegee and paper towel. Not only is does Rapid Remover work fast, but it works without causing damage to most painted or bare metal surfaces. What may have been a four-hour job (and a messy one at that) can now be cut in half with an easy, clean and non-damaging removal. Gone are the days of using dangerous and risky chemicals that often damaged painted surfaces, and had numerous health hazards. Rapid Remover works. It’s that simple.
Change is good. Back in the day choosing a vinyl film was easy with basically two film types, cast, and calendered. Nowadays things are a little different. Sign and graphics professionals now hove more types of vinyl films to choose from than ever, with more adhesive types as well. We developed Rapid Tac II to work with a wider variety of films such as the economy calendered, intermediate calendered, high performance calendered, metallic, reflective, polyester, mylar and other specialty films). Rapid Tac II promotes bonding faster than the original Rapid Tac application fluid and is ideal for cold weather and glass application. Rapid Tac II is not a replacement for the Original Rapid Tac, and may bond too fast with “Premium Cast” films in warmer conditions.
Preparation is the key to success. With an ever growing need for a safer workplace, we developed a pre cleaner that not only works great, but is safe to use. Gone are the days of using flammable and hazardous chemicals to pre-clean with. Wax, grease, oil and silicone residues are the number one reason for both paint and film application failures. Rapid Prep easily and safely eliminates these and other contaminants ensuring a successful paint or film application, and a happy customer. Ideal for pre cleaning almost any surface including automobile paint, bare metals, sign materials and glass, Rapid Prep was formulated by people with hands on experience and a desire to make a safer more effective pre-cleaner.
Rapid Clear is the perfect end to a job well done and will make your work look it’s best. Easily clean and polish plexiglass, glass, and most polycarbonates, while leaving a luster that is sure to impress. Use Rapid Clear as a final cleaning for your sign work, auto restoration, etc. Rapid Clear is Non-Hazardous Non-Flammable Bio-Degradable.Perfect For:Household Glass Auto GlassAircraft Windows Marine Windows TV Screens Computer Monitors Tinted Glass Eye Wear Safety Shields Cameras Optical Equipment
Hinge Handle One offers all the great features of Hinge Handle Classic—plus is even quicker to install since tee-nuts and screws are not required. Simply staple or screw Hinge Handle One to the sign board—and you're ready to go. For larger signs, just use two—one size fits all. Hinge Handle One is made from a high-strength composite polymer, making it completely rust-proof and virtually unbreakable even in cold weather.
Sign Link is the perfect solution for installing signs to chain-link fences and channel sign posts. It's a new patent-pending product made of 33% glass-filled nylon with a threaded center insert (in two sizes: 5/16" coarse and 8mm coarse). Sign Link fits all chain-link grid sizes. Sign Links come with lifetime warranty.
Sign Feet are high-strength flexible polyethelene-injected parts that improve Sign Boards—and any kind of A-frame sign—in several ways
Sign Brackets allow signmakers to quickly and easily install large outdoor signs—without having to dig holes or construct heavy, complex support systems. With Sign Brackets, you can fasten four pre-cut 2-by-4s to a 4-by-8 sign board in just a few minutes. Sign Brackets are made from 3/16" plate steel, and powdered-coated to produce a smooth, durable finish that will last many years, even in harsh conditions
Pro Klip Mini is designed for banner material. The rope or hook used to hang the banner pulls on the wedge such that: The greater the pull, the stronger the grip. To release the grip, simply squeeze Pro Klip (for example, with pliers) and the wedge and clip will loosen.
Pro Klip Super is designed for thicker materials, such as 4mm Coroplast or 3mm Sintra. Pro Klip Super uses a ratchet design to fasten itself to the material. Unfastening Pro Klip Super is easy: Simply push down on the ratchet and pull back. Pro Klip super is ideal for installing heavy signs in stores that hang from the ceiling plus dozens of other applications.